在使用電動卷簾門的過程中，難免會遇到這樣或那樣的問題。不要一遇到問題就打電話報修。有很多小問題。自己幾分鐘就能解決。下面濟南卷簾門廠家為您分析：

In the process of using the electric roller shutter door, it is inevitable to encounter some problems. Don't call for repair as soon as you encounter problems. There are many small problems. You can solve it in a few minutes. Jinan roller shutter manufacturer will analyze for you:

1.簾布一直上下擺動

1. The cord fabric keeps swinging up and down

這個問題可能是由于機械卡阻或潤滑不良造成的。檢查機械負載。機械中可能存在共振現象。調整載波，改變減速比，避開諧振頻率，安裝阻尼墊片。

This problem may be caused by mechanical jamming or poor lubrication. Check the mechanical load. Resonance may exist in the machine. Adjust the carrier wave, change the reduction ratio, avoid the resonance frequency, and install the damping gasket.

2.不要急著報修，先調試

2. Don't rush to repair, debug first

卷簾門向上時，承重問題是常見的。如果不確定是不是軸承問題，建議先把負載從電機上斷開。確定是電機問題還是負載問題。在打開或關閉電機之前，用手關閉電機，并檢查它是否有卡住的感覺。有一種電機卡死的感覺，電機連接線互不接觸，控制器壞了。如果電機轉動，但門不運行，可能需要更換電容器。如果排除電機問題，門體運行軌跡中可能存在雜質，這些雜質的存在會阻礙門體的運行。

When the roller shutter door is upward, the bearing problem is common. If you are not sure whether it is a bearing problem, it is recommended to disconnect the load from the motor first. Determine whether it is a motor problem or a load problem. Before opening or closing the motor, close the motor by hand and check whether it feels stuck. There is a feeling that the motor is stuck. The connecting wires of the motor do not touch each other, and the controller is broken. If the motor rotates but the door does not operate, the capacitor may need to be replaced. If the motor problem is eliminated, there may be impurities in the running track of the door body, which will hinder the operation of the door body.

3.卷簾總是不受控制地滑下。

3. The roller shutter always slides down uncontrollably.

可能是剎車壞了或者卡在機器里的什么東西壞了，也可能是剎車不夠緊卡住了卷閘門。電動卷閘門要有機械鎖緊部件，就是能卡住卷閘門卷筒的那種。檢查一下。如果真的壞了，就需要更換了。如果一次不卡，可以再上下調試一次。

The brake may be broken or something stuck in the machine may be broken, or the brake may not be tight enough to jam the shutter. The electric rolling gate shall have mechanical locking parts, which can block the rolling gate drum. Check it. If it really breaks, it needs to be replaced. If it doesn't get stuck at one time, you can debug it up and down again.

4.遙控器打不開卷簾門

4. The remote control cannot open the roller shutter door

，安裝調試過程中有沒有問題？如果安裝調試過程中沒有問題，一般的電機和繞線輪都不會有問題。那么通常會考慮無線遙控。遙控器是否已設置、通電且有損壞？如果是用了很久的老卷簾門，遙控器的問題排除了，那就用開關操作一下，看看電機是否還在工作。電機沒有聲音，繞線輪不工作，你需要考慮更換電機。

First of all, are there any problems during installation and debugging? If there are no problems during installation and commissioning, the general motor and winding wheel will not have problems. Then wireless remote control is usually considered. Is the remote control set, powered on and damaged? If the problem with the remote control is eliminated for the old rolling shutter door that has been used for a long time, use the switch to operate it to see if the motor is still working. The motor has no sound and the winding wheel does not work. You need to consider replacing the motor.

5.如何調整卷簾門的“行程”

5. How to adjust the "travel" of the roller shutter door

按照安裝手冊的說明，輸入初始密碼，進入“設置”，然后進入“行程設置”，再根據自己的需要進行調整。

First, according to the instructions in the installation manual, enter the initial password, enter "Settings", then enter "Travel Settings", and then adjust according to your needs.

6.如何檢修內部接線

6. How to repair internal wiring

打開簾布右側的“控制箱”進行檢查。

Open the "control box" on the right side of the cord for inspection.

7.卷簾門會突然自己打開

7. The shutter door will suddenly open by itself

可能是電動滑動門裝了雷達感應器。當雷達接觸到傳感器時，它會自動打開。建議晚上不用卷簾門時，建議鎖好，切斷電源。

It may be that the electric sliding door is equipped with a radar sensor. When the radar contacts the sensor, it will turn on automatically. It is recommended to lock the shutter door and cut off the power supply when it is not used at night.

8.卷簾門可以手動控制嗎？

8. Can the roller shutter be manually controlled?

是的。在控制盒中設置，按鍵進入“行程”，進行“模式設置”，然后選擇“手動模式”。調試時一定要注意。

yes. Set in the control box, press the key to enter "Travel", perform "Mode setting", and then select "Manual mode". Pay attention to safety during commissioning.

9.卷簾門為什么會咔嚓一聲？

9. Why does the shutter door click?

通常情況下，模式設置為“點擊”模式，因此您可以重新輸入行程設置并修改模式。更改為“手動”或“自動”。電動卷簾門向上無法排除電機問題。通常認為是控制鍵壞了，需要打開控制鍵盒的面板進行維修。

Normally, the mode is set to "click" mode, so you can re-enter the trip setting and modify the mode. Change to Manual or Automatic. The motor problem cannot be eliminated when the electric shutter door is upward. It is generally believed that the control key is broken, and the panel of the control key box needs to be opened for maintenance.

電動卷簾門故障排除的9個小技巧相關內容就講解到這里了，您對此有怎樣的疑惑或者需求，就來我們網站http://99feipin.cn咨詢！

Here are the 9 tips for troubleshooting electric roller shutter doors. If you have any doubts or needs, please come to our website http://99feipin.cn consulting service