The rolling shutter garage door not only has good protective performance, but also can meet different size requirements without occupying the internal space of the garage, saving space. It is not only suitable for household garages, but also suitable for some commercial storefronts, garages, hospitals, theaters and other public places.

卷簾車庫門一般情況下是不會受到限制的，它制作的高度可到9米-14米，制作的寬度可達到4米-12米;卷簾車庫門尺寸的大小，主要是根據車庫整體的高度和寬度來定。

Rolling shutter garage doors are generally not restricted, as they can be made to a height of 9-14 meters and a width of 4-12 meters; The size of the rolling shutter garage door is mainly determined by the overall height and width of the garage.

1、一般小型的單車庫(寬度在3米以內，高度在2.5米以內)選用的卷簾車庫門型號是55型號或者是77型號的簾片;2、因?yàn)闈?jì)南電動卷簾門的大小主要是根據車庫整體的高度和寬度來決定的，所以大型的雙車庫選擇的卷簾門是7型號的簾片。

1. Generally, for small single garages (with a width of less than 3 meters and a height of less than 2.5 meters), the rolling shutter garage door model selected is either 55 or 77; 2. Because the size of Jinan electric roller shutter doors is mainly determined by the overall height and width of the garage, the roller shutter door selected for large double garages is a 7 model curtain.

注意事項：

Precautions:

1、安裝卷簾車庫門之前，在需要安裝的門框框口畫線，定好尺寸大小后，再找相關人員設計出合理的卷簾門;濟南卷簾門

1. Before installing the rolling shutter garage door, draw lines on the door frame opening that needs to be installed, determine the size, and then find relevant personnel to design a reasonable rolling shutter door; Jinan rolling shutter door

注意：框內的高度要比門扇的高度要高一點。

Note: The height inside the frame should be slightly higher than the height of the door leaf.

2、拆掉門框下部的固定板，再把卷簾車庫門的門框固定好，這時候一定注意洞口兩側的地面要預留凹槽，然后固定木楔;3、當你在安裝卷簾車庫門的主體門扇時，要讓卷簾門和墻體是連成整體的，封閉性一定要做好。然后粉刷墻體和卷簾門與墻體之間的縫口，粉刷過后要保障門縫均勻平整，這樣你在開車庫門的時候才會輕便自由。

2. Firstly, remove the fixing plate at the bottom of the door frame, and then fix the door frame of the rolling shutter garage door. At this time, be sure to reserve grooves on the ground on both sides of the hole, and then fix the wooden wedge; 3. When installing the main door leaf of the rolling shutter garage door, make sure that the rolling shutter door and the wall are connected as a whole, and ensure good sealing. Then paint the wall and the seam between the rolling shutter door and the wall. After painting, ensure that the door seam is even and flat, so that you can easily and freely open the garage door.